Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands Manual de usuario Pagina 40
- Pagina / 142
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3.2 Commands Details
3-9
3
Commands for Preparation Process
3.2.4 Start Synchronous Communications (SYNC_SET: 0DH)
This section describe how to start synchronization to change a communications phase from phase 2 to phase 3.
When SYNCMOD bit of the COM_MOD of CONNECT command is set to 1, the communications phase will
change from phase 1 to phase 3 at the moment the connection is established. In this case, it is not necessary to
send a SYNC_SET command.
(1) SYNC_SET Command (0DH)
The specifications of the SYNC_SET command are described below.
Byte
SYNC_SET
Description
Command Response
10DH 0DH
Phases in
which the
command can
be executed
Phase 2
Synchronization
classification
Asynchronous
command
2ALARM
Processing
time
Communications
cycle or more
(Within 5 s)
Subcommand Cannot be used
3
STATUS • Starts synchronous communications. Switched from phase 2 to phase 3.
• Synchronization is made at the WDT changing edge. However, if WDT
errors are masked by parameter Pn800.0, processing is completed when
this command is received.
• During phase 3, the slave ignores this command and returns a normal
response without a warning.
• If the slave station in Servo ON status receives this command in phase 2,
the slave station enters Servo OFF status.
• At occurrence of the following alarms and warnings, this command must
be transmitted to restart synchronous communications.
- Command warning 1 (A.95A) occurs when this command is used in
phase 1
- MECHATROLINK-II synchronization Error (A.E50)
- MECHATROLINK-II synchronization failed (A.E51)
- MECHATROLINK-II Communications Error (A.E60)
- MECHATROLINK-II Transmission Cycle Error (A.E61)
- Command warning 1 (A.95A) occurs when this command is used while
operating the servo using SigmaWin or a digital operator.
4
5
6
7
8
9
10
11
12
13
14
15
16 WDT RWDT
- Σ-V Series 1
- About this Manual 3
- Warranty 4
- (3) Suitability for Use 5
- (4) Specifications Change 5
- Contents 6
- 1.1.1 Layers 10
- 1.1.2 Frame Structure 10
- MECHATROLINK-II Commands 11
- 1.1.4 Terminology 12
- 1 MECHATROLINK-II Commands 14
- 1.4 Data Order 17
- Operation Sequence 18
- 2.1 Preparing for Operation 19
- Setting the Station Address 20
- 2 Operation Sequence 21
- -J11) are Used 23
- (1) Operation Procedure 25
- Controller 26
- 2.3.1 Setup Sequence 27
- POS: Reference position 31
- 3.2.1 No Operation (NOP: 00H) 34
- (4) Details WDT and RWDT 36
- (1) DISCONNECT Command (0FH) 37
- (1) CONNECT Command (0EH) 38
- (2) Details of COM_MOD 39
- (1) SYNC_SET Command (0DH) 40
- (1) ID_RD Command (03H) 41
- (2) Device ID Specifications 42
- ID_RD aSGDV2R9E11A00 43
- ID_RD bSGDV131J11A00 44
- (1) PRM_WR Command (02H) 45
- (1) PPRM_WR Command (1CH) 46
- (1) CONFIG Command (04H) 47
- (1) SENS_ON Command (23H) 48
- • Applicable Commands: 50
- (1) SV_ON Command (31H) 51
- 3.2 Commands Details 52
- (1) SENS_OFF Command (24H) 54
- (1) SV_OFF Command (32H) 55
- (1) PRM_RD Command (01H) 56
- (1) SMON Command (30H) 57
- (1) ALM_RD Command (05H) 58
- (2) ALM_RD_MOD Specifications 59
- (1) ALM_CLR Command (06H) 60
- (1) POS_SET Command (20H) 61
- (2) PS_SUBCMD Specifications 61
- (1) ADJ Command (3EH) 62
- C01EH reference value 65
- C021H reference value 65
- Motion Commands for Operation 66
- 4.1 Motion Commands List 67
- 4.2.1 Stop Motion (HOLD: 25H) 68
- (2) Related Parameters 69
- (1) LTMOD_ON Command (28H) 70
- (2) Normal Latch Mode 70
- (3) Continuous Latch Mode 71
- (4) LT_SGNL Specifications 72
- (5) Related Parameters 72
- (1) LTMOD_OFF Command (29H) 73
- (1) INTERPOLATE Command (34H) 74
- (1) POSING Command (35H) 76
- (1) FEED Command (36H) 78
- (1) LATCH Command (38H) 80
- (1) EX_POSING Command (39H) 82
- (2) Operation 83
- (3) Related Parameters 83
- 4.2.9 Homing (ZRET: 3AH) 84
- (1) VELCTRL Command (3CH) 86
- Before soft-start 87
- After soft-start 87
- Max. motor speed 87
- Pn305 Pn306 87
- (1) TRQCTRL (3DH) 88
- (2) Speed Limit Option 1 89
- (3) Speed Limit Option 2 89
- 5.2.1 Electronic Gear Setting 93
- Position 94
- (2) Position Reference Filter 96
- 5.2.3 Motion Sequence Setting 99
- 5.2.4 Command Data Options 100
- 5 Command Related Parameters 101
- 5.2.4 Command Data Options 101
- (4) OPTION Field Allocation 102
- (1) Latching Allowable Area 104
- (2) Continuous Latch Function 104
- Command Related Parameters 106
- NEAR Signal Width Setting 111
- (3) Option Monitor Setting 113
- MECHATROLINK-II Subcommands 114
- 6.2.1 No Operation (NOP: 00H) 115
- Data Field 120
- 7.1 Main Command Data Field 121
- (1) Applicable Commands 123
- (2) Setting Method 125
- Applicable Commands 126
- 7.1.6 LT_SGNL Specifications 128
- 7.2 Substatus Data Field 129
- Communications or Commands 130
- 8.1 List of Alarms 131
- 8.1 List of Alarms 132
- 8.2 List of Warnings 133
- 8.2 List of Warnings 134
- Appendix 136
- A Brake Control Commands 137
- • Sub-control (SUBCTRL) 139
- Select Motion (MOTION) 140
- Select Latch Signal (L_SGN) 140
- • Sequence Signals: SQ_CMD 140
- Revision History 141
Relacionado con productos y manuales para Equipo Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands
(460 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales