Yaskawa Profibus-DP Option Card CM061 Manual de usuario Pagina 65
- Pagina / 68
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting D-13
# Module Status Indicators
The following LEDs indicates the status of the PROFIBUS-DP Option.
Table D.7 – Diagnostic LEDs
LED Color Indication/Function
PWR Green Lit when the +5V power to the electronics is OK.
Turned off if the +5V is below +4.5V (min)
Indicates the module status
OFF Communication Option CPU not running.
Solid Green: Initialization.
Flashing green: Normal operation.
Solid Red: Internal Communication Option error.
Flashing red: error detected.
WD Red/Green
Other indication Unspecified, Communication Option error
# LED Diagnostics
The following table presents the faults displayed by the LEDs on the PROFIBUS-DP Option, their causes, and corrections.
Table D.8 – LED Diagnostics
LED Display
PWR COM ERR WD
Content Cause Corrective Action
Power is not being supplied
from the drive.
• Check the main circuit wiring on the drive.
• Cycle drive power.
OFF OFF OFF OFF
Power
OFF
Power is not being supplied to
the option unit due to poor
option unit connection.
• Turn of the drive power.
• Check the option unit connection to the
drive.
• Cycle drive power.
Solid
Green
OFF
Solid
Red
Solid
Red
CPU
Error
Option unit CPU error.
• Cycle drive power.
• Replace option unit if fault persists.
Solid
Green
OFF
Solid
Red
Flashing
Red
Drive
Error
Error in Drive unit.
• Cycle drive power.
• Replace drive if fault persists.
Solid
Green
OFF
Flashing
Red
Solid
Green
Com
Error
A fault has occurred rendering
communication impossible.
• Check whether the address set in the
PROFIBUS-DP Master differs from the
address of the option unit.
• Check that the master is functioning
properly.
• Check that the termination resistor is
correctly connected to the communication
line.
• Check whether the communication line is
correctly connected (disconnected or poor
connection).
• Check that the communication line is
separated from the main power line.
Solid
Green
Solid
Green
Flashing
Red
Solid
Green
Com
Error
A fault has occurred rendering
communication impossible.
• Check whether the address is duplicated
with any other devices within the
PROFIBUS-DP network.
Solid
Green
Solid
Green
OFF
Solid
Green
CPU
Init
Option unit under initialization
• Wait until the WD LED is flashing
Solid
Green
Solid
Green
OFF
Flashing
Green
Normal
Normal communication
possible.
- Option 1
- Warnings and Cautions 3
- Introduction 4
- Table of Contents 5
- Chapter 1 Installation 7
- Installation 1-2 8
- Installation Check Sheet 9
- Installation 1-4 10
- Unpack and Inspect 11
- Installation and Wiring 12
- Installation 1-7 13
- # Set Node Address 14
- # Set Network Termination 14
- Installation 1-9 15
- Option LEDs 16
- # LED Diagnostics 17
- Drive Faults 18
- Network Configuration 2-1 19
- Network Configuration 2-2 20
- Configuration 21
- # Select Station Type 22
- # Station Configuration 22
- Network Configuration 2-5 23
- GSD File 24
- Network Communications 3-2 26
- 16 Word Input/Output Message 27
- # Fast I/O Output Data 28
- # Fast I/O Input Data 29
- # Parameter Access Area 29
- Network Communications 3-6 30
- 6 Word Input/Output Message 31
- Network Communications 3-9 33
- 3 Word I/Os Message 34
- Network Communications 3-12 36
- Handshaking 37
- Network Communications 3-14 38
- Product Specification A-1 39
- Product Specification A-2 40
- Product Specification B-1 41
- Product Specification B-2 42
- Product Specification B-3 43
- Product Specification B-4 44
- Appendix C Parameter Access 45
- Parameter Access C-2 46
- Parameter Access Overview 47
- Parameter Access C-4 48
- Read Drive Data Example 49
- Parameter Access C-6 50
- Write Drive Data Example 51
- Parameter Access C-8 52
- Appendix D Troubleshooting 53
- Troubleshooting D-2 54
- Troubleshooting Check List 55
- Troubleshooting D-4 56
- Troubleshooting D-5 57
- Troubleshooting D-6 58
- Troubleshooting D-7 59
- Wiring And Cabling 60
- Troubleshooting D-9 61
- # Cable Is Routed Correctly 62
- PROFIBUS-DP Configuration 63
- # LED Indicators 64
- # Module Status Indicators 65
- # Drive Faults 66
- PROFIBUS-DP 68
Relacionado con productos y manuales para Equipo Yaskawa Profibus-DP Option Card CM061
Equipo Yaskawa E7 Apogee FLN Manual de usuario
(57 paginas)
(57 paginas)
Equipo Yaskawa DriveWizard AC Drive Manual de usuario
(154 paginas)
(154 paginas)
Equipo Yaskawa E7B Drive Bypass Manual de usuario
(178 paginas)
(178 paginas)
Equipo Yaskawa G5HHP Drive Manual de usuario
(374 paginas)
(374 paginas)
Equipo Yaskawa MP920 Motion Module Manual de usuario
(450 paginas)
(450 paginas)
Equipo Yaskawa MP940 Manual de usuario
(522 paginas)
(522 paginas)
Equipo Yaskawa CIMR-LE Manual de usuario
(520 paginas)
(520 paginas)
Equipo Yaskawa Sigma-5 SGDV Manual de usuario
(21 paginas)
(21 paginas)
Equipo Yaskawa AC Drive-A1000 Manual de usuario
(18 paginas)
(18 paginas)
Equipo Yaskawa PID A1000 Manual de usuario
(13 paginas)
(13 paginas)
Equipo Yaskawa CIMR-AU 200V Manual de usuario
(840 paginas)
(840 paginas)
Equipo Yaskawa MP900 Teach Pendant Manual de usuario
(80 paginas)
(80 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales