Yaskawa MP900 Series Ladder Programming Manual Manual de usuario Pagina 312
- Pagina / 415
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5.10 System Function Instructions
5.10.6 Send Message (MSG-SND)
5-243
Instructions
5
[ a ] Parameter Details
This section describes the parameters in detail. The parameter number corresponds to the word offset from the first
address of the parameter list.
For example, if the first address of the parameter list is MA00100, set the value in MW00110 to set PARAM10.
Processing Result (PARAM00)
This parameter outputs the result of processing to the upper byte. The lower byte is used for system analysis.
• 00 hex: Processing (Busy)
• 10 hex: Processing completed (Complete)
• 8 hex: Error
The following errors can occur.
•81 hex: Function code error
An attempt was made to send an unused function code. Or an unused function code was received.
•82 hex: Address setting error
The data address, coil offset, input relay offset, input register offset, or hold register offset is out-
side of the valid range.
•83 hex: Data size error
The size of the send or receive data was set outside of the valid range.
•84 hex: Circuit number setting error
The set circuit number is outside of the valid range.
•85 hex: Channel number setting error
The set channel number is outside of the valid range.
•86 hex: Station address error
The set station number is outside of the valid range.
•88 hex: Communications section error
The communications section returned an error response.
•89 hex: Device selection error
A device that cannot be used was selected.
Parameter No. IN/OUT
Description
MEMOBUS No-protocol
PARAM00 OUT
Processing result Processing result
PARAM01 OUT
Status Status
PARAM02 IN
Remote station number Remote station number
PARAM03 SYS
Reserved for system. Reserved for system.
PARAM04 IN
Function code –
PARAM05 IN
Data address Data address
PARAM06 IN
Data size Data size
PARAM07 IN
Remote CPU number Remote CPU number
PARAM08 IN
Coil offset –
PARAM09 IN
Input relay offset –
PARAM10 IN
Input register offset –
PARAM11 IN
Hold register offset Register offset
PARAM12 SYS
Reserved for system. Reserved for system.
PARAM13 SYS
Reserved for system. Reserved for system.
PARAM14 SYS
Reserved for system. Reserved for system.
PARAM15 SYS
Reserved for system. Reserved for system.
PARAM16 SYS
Reserved for system. Reserved for system.
- USER'S MANUAL 1
- LADDER PROGRAMMING 1
- About this Manual 3
- Using this Manual 3
- MP2000-series Manuals 3
- Related Manuals 4
- Safety Information 6
- Safety Precautions 7
- Warranty 8
- ( 3 ) Suitability for Use 9
- ( 4 ) Specifications Change 9
- Contents 10
- Revision History 15
- Controllers 18
- 1.2.2 Program Modules 19
- SIEP C880732 01) for details 20
- Optional Module 30
- 3.1.4 System Startup 31
- 3.1.5 Creating a Project 32
- 2. Click the OK Button 33
- Right-click 34
- Drag and drop 34
- IMPORTANT 35
- Double-click 38
- Enter “MB000000.” 38
- 2. Click the Start Button 41
- Programming 42
- 4.1 Ladder Program Editor 43
- 4.2 Ladder Drawings 44
- 4.3 User Functions 48
- Enter “FUNC01.” 50
- 4.4 Registers (Variables) 54
- 4.4.2 Register Types 55
- ( 2 ) Local Registers 56
- 4.4.3 Data Types 58
- 4.4.4 Index Registers (i, j) 60
- 4.5 Table Data 62
- 4.5.2 Creating Table Data 63
- 4.6 Transferring Data 64
- 4.8 Advanced Programming 66
- 4.8.2 C-language Programs 67
- 4.8.3 Security 68
- Project Password Setting 68
- Program Password Setting 68
- Online Security Setting 68
- 4.8.4 Tracing 69
- Realtime Tracing 69
- Data Tracing 69
- XY Tracing 69
- 5.2.1 NO Contact (NOC) 74
- 5.2.2 NC Contact (NCC) 75
- 5.2.9 Coil (COIL) 88
- 5.2.10 Set Coil (S-COIL) 89
- 5.2.11 Reset Coil (R-COIL) 90
- 5.3.1 Store (STORE) 91
- 5.3.2 Add (ADD (+)) 93
- 5.3.4 Subtract (SUB (−)) 97
- ( 3 ) Programming Examples 100
- 5.3.6 Multiply (MUL (x)) 101
- Instructions 102
- 5.3.7 Divide (DIV (÷)) 103
- ( 1 ) Operation 105
- ( 2 ) Format 105
- 5.3.9 Real Remainder (REM) 107
- Condition n 107
- Key entry: INC 109
- 5.3.11 Decrement (DEC) 111
- Output Data Behavior 111
- 5.3.12 Add Time (TMADD) 113
- ( 3 ) Programming Example 114
- 5.3.13 Subtract Time (TMSUB) 115
- 5.3.14 Spend Time (SPEND) 117
- 5.3.15 Invert Sign (INV) 120
- 5.3.17 Absolute Value (ABS) 122
- 5.3.19 BCD Conversion (BCD) 124
- 5.4.1 Inclusive AND (AND) 132
- 5.4.2 Inclusive OR (OR) 134
- 5.4.3 Exclusive OR (XOR) 136
- 5.4.4 Less Than (<) 138
- Input data AInput data B 139
- Key entry: <= 139
- 5.4.6 Equal (=) 140
- 5.4.7 Not Equal (≠) 141
- Key entry: > 143
- 5.4.10 Range Check (RCHK) 144
- Work Register Configuration 147
- Parameter Table Configuration 151
- First address of 153
- ( 4 ) Additional Information 159
- Variable > Maximum value? 160
- 5.6.1 Square Root (SQRT) 168
- 5.6.2 Sine (SIN) 170
- Input data 172
- Output data 172
- 5.6.5 Arc Sine (ASIN) 175
- Input Data Range 175
- 5.6.6 Arc Cosine (ACOS) 176
- 5.6.7 Arc Tangent (ATAN) 177
- Input data Output data 179
- 5.7 Data Shift Instructions 181
- 5.7.3 Move Bit (MOVB) 185
- 5.7.4 Move Word (MOVW) 187
- 5.7.5 Exchange (XCHG) 189
- 5.7.9 Binary Search (BSRCH) 197
- 5.7.10 Sort (SORT) 199
- 5.7.13 Copy Word (COPYW) 205
- 5.7.14 Byte Swap (BSWAP) 207
- 5.8 DDC Instructions 208
- Input value Output value 210
- Dead zone set value 210
- Key entry: DZB 210
- 5.8.4 PI Control (PI) 214
- 5.8.5 PD Control (PD) 219
- 5.8.6 PID Control (PID) 225
- 5.8.7 First-order Lag (LAG) 230
- 5.8.8 Phase Lead Lag (LLAG) 233
- If DVDTS = ON, DVDT = 250
- (V – V' ) × 5,000 250
- DVDT = V - V’ 251
- (DB000001) three times 291
- Error Codes 293
- 5.10.1 Counter (COUNTER) 294
- Key entry: TRACE 301
- Structure of Read Data 303
- Processing Result (PARAM00) 312
- Status (PARAM01) 313
- Function Code (PARAM04) 314
- Data Addresses 315
- Key entry: MSG-RCV 323
- Status (PARAM01) 324
- Data Address (PARAM05) 325
- Data Size (PARAM06) 325
- Remote CPU Number (PARAM07) 325
- Error Code (PARAM01) 341
- Copy of Cir-No (PARAM02) 341
- Copy of St-No (PARAM03) 341
- For System Use #1 (PARAM04) 341
- For System Use #2 (PARAM05) 342
- For System Use #3 (PARAM06) 342
- ON coils are 356
- Current values of 356
- 6.2 Searching/Replacing 357
- 6.3 Cross References 358
- 6.5 Forcing Coils ON and OFF 359
- 6.6 Viewing Called Programs 360
- 6.7 Register Lists 360
- 6.8 Tuning Panel 361
- Ladder drawing 362
- MPE720 version 6 363
- Troubleshooting 364
- 7.2 Indicator Status 366
- 7.3 Problem Classifications 367
- 7.4 Detailed Troubleshooting 369
- Troubleshooting Method 2 371
- 7.4.2 I/O Errors 372
- 7.4.3 Watchdog Timer Errors 373
- 7.4.5 System Errors 374
- Appendix A 375
- A.1 System Service Registers 376
- ( 2 ) Exclusive to DWG.H Only 377
- ( 3 ) Exclusive to DWG.L Only 378
- System Registers 379
- A.2 System Status 380
- A.3 System Error Status 381
- A.3 System Error Status 382
- Error Code 383
- Index error 383
- A.7 System I/O Error Status 386
- A.9 Interrupt Status 388
- A.10 Module Information 389
- A.11 MPU-01 System Status 390
- Appendix B 393
- Programs 394
- 2. Click Select 396
- Appendix C 397
- Configuration Example 398
- Ladder Programming Example 398
- C.2 Motion Program Control 399
- Motion Programming Example 400
- Procedure 402
- Appendix D 403
- ( 1 ) Operators 404
- ( 2 ) Operands 405
- D.2 National Limitations 407
- D.2.4 Substitution Operator 408
- D.2.5 Functions 408
- D.2.6 Others 408
- Arrays 408
- Appendix E 409
- E.1 General Precautions 410
Relacionado con productos y manuales para Equipo Yaskawa MP900 Series Ladder Programming Manual
Equipo Yaskawa MP930 Manual de usuario
(318 paginas)
(318 paginas)
Equipo Yaskawa Sigma Mini Manual de usuario
(282 paginas)
(282 paginas)
Equipo Yaskawa MEMOCON GL120 Manual de usuario
(495 paginas)
(495 paginas)
Equipo Yaskawa Varispeed 626M5 Manual de usuario
(305 paginas)
(305 paginas)
Equipo Yaskawa Sigma II Series SGMVH Manual de usuario
(339 paginas)
(339 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales